package octez-shell-libs

  1. Overview
  2. Docs
package octez-shell-libs
Legend:
Library
Module
Module type
Parameter
Class
Class type
type listening_socket_open_failure = {
  1. reason : Unix.error;
    (*

    The error we are re-raising

    *)
  2. address : Tezos_base.TzPervasives.P2p_addr.t;
    (*

    The interface we are trying to listen to

    *)
  3. port : int;
    (*

    The port we are trying to listen to

    *)
}

Type describing an opening failure for the listening socket.

type Tezos_base.TzPervasives.error +=
  1. | Failed_to_open_listening_socket of listening_socket_open_failure

Type of an error in case of the listening socket fails to open.

This module defines a type t which wraps a file descriptor. Most functions simply call the underlying file descriptor function and generate logs with prefix "p2p.fd".

type t
type unexpected_error = [
  1. | `Unexpected_error of exn
]

`Unexpected_error is a generic case of error that is used by default to represent a raising error that cannot be identified as a known error case.

Note: This errror is needed in general to address unexpetected exception that could be raised during fd processing. Though, it is not encouraged to use it. It is a better practice to catch exceptions and convert them explicitly to a dedicated (polymorphic) variant type.

type read_write_error = [
  1. | `Connection_closed_by_peer
  2. | `Connection_lost of exn
  3. | `Connection_locally_closed
  4. | unexpected_error
]

read_write_error is used by the functions read or write in case of error.

`Connection_closed_by_peer is returned when the socket returns 0 bytes read or written.

`Connection_lost is returned when the connection was closed because of a timeout or another problem related to the remote peer.

`Connection_locally_closed is returned when the connection's socket has been locally closed before we try to access it.

type connect_error = [
  1. | `Connection_failed
  2. | unexpected_error
]
type accept_error = [
  1. | `System_error of exn
  2. | `Socket_error of exn
  3. | unexpected_error
]

accept_error is used in case of error while trying to accept some connection.

`System_error represents system-wide errors which are related to the state of whole process or computer. These are errors that will probably reoccur at next accept and must be treated accordingly (for example by giving some time to the system to recover).

`Socket_error represents socket-specific errors which are related to the one connection that the function attempted to accept. These are usually temporary errors related to network delays or remote host responsiveness . For most socket-errors you can just log them and call accept again to be ready for the next connection.

val pp_read_write_error : Format.formatter -> read_write_error -> unit

Pretty printer for read_write_error.

val id : t -> int

id t returns a unique, positive, identifier for t. Identifiers are generated sequentially at creation time.

val set_point : point:Tezos_base.TzPervasives.P2p_point.Id.t -> t -> unit

set_point ~point t sets the point where fd is or will be connected to.

val set_peer_id : peer_id:Tezos_base.TzPervasives.P2p_peer.Id.t -> t -> unit

set_peer_id ~peer_id t sets the peer id where fd is or will be connected to.

val close : ?reason:P2p_disconnection_reason.t -> t -> unit Lwt.t

close ?reason fd closes the connection and the underlying fd. It is idempotent.

val add_closing_reason : reason:P2p_disconnection_reason.t -> t -> unit

Stores in the fd a reason for which it will be closed in a near future.

val read : t -> Tezos_base.TzPervasives.Bytes.t -> int -> int -> (int, read_write_error) result Lwt.t

read fd buf ofs len reads up to len bytes from fd, and writes them to buf, starting at offset ofs. If the operation leads to a `Connection_lost error it is guaranteed that the underlying socket has been closed.

write fd buf writes all bytes from buf to fd. If the operation leads to a `Connection_lost error it is guaranteed that the underlying socket has been closed.

val socket : unit -> t Lwt.t

Returns a fresh fd. This call always succeed.

val create_listening_socket : ?reuse_port:bool -> backlog:int -> ?addr:Ipaddr.V6.t -> int -> Lwt_unix.file_descr Tezos_base.TzPervasives.tzresult Lwt.t

create_listening_socket ?reuse_port ~backlog ?addr port creates a socket that listens on addr or Ipaddr.V6.unspecified if addr is not provided and on port.

reuse_port is used to set Unix socket option SO_REUSEPORT. If reuse_port is not provided this option is set to false. SO_REUSEADDR is set to true.

backlog set the maximum number of pending connections.

val connect : t -> Lwt_unix.sockaddr -> (unit, connect_error) result Lwt.t

connect fd addr connects fd to addr. If there is an error, fd is closed.

accept sock accepts connections on socket sock.

OCaml

Innovation. Community. Security.

GitHub Discord Twitter Peertube RSS
About
Changelog Releases Industrial Users Academic Users Why OCaml
Ecosystem
Packages Community Events OCaml Planet Jobs
Resources
Install OCaml Get Started Platform Tools Language Manual Standard Library API Books Exercises Papers OCaml Playground Logo
Policies
Carbon Footprint Governance Privacy Code of Conduct